In the last week or so, I’ve had many calls about fall fertilizer applications on fescue and brome pastures and meadows. Much of the nitrogen (N) applied to tall fescue and smooth bromegrass hay meadows and pastures goes on in January or February in eastern Kansas but fall is the best time to apply phosphorus (P) and potassium (K) for the spring growing season. The amount of N-P-K depends heavily on forage use such as grazing vs haying.
Normal N fertilization rates for established fescue and bromegrass hay fields are 90 to 120 pounds actual N per acre, or about 30 pounds of N per ton of expected yield. A summary of K-State N response data shows the average yields for unfertilized brome and fescue were about 1.4 tons of hay per acre, while maximum yields averaged 3.2 tons of hay with 140 pounds of N. Protein levels will also be increased at the higher N fertilizer rates, assuming timely harvest. In cases where producers are relying on high-quality hay as their primary protein source, they will want to push N rates to the upper end of the recommended range.Timing of N application is another factor to consider. While most growers apply all the N and any needed P and K for hay production in a single application in the spring, research in Kansas has shown that applying all the fertilizer in the fall will normally result in slightly higher yields, though the protein values will normally be slightly lower. Prior K-State research indicates that smooth brome responded to spring applications as late as April without effects on tonnage of dry matter produced and significantly greater crude protein levels than fall applications. Fall applications of N and P stimulate root growth and produce more tiller buds, resulting in more stems the following spring. Under normal conditions, tall fescue and smooth bromegrass pastures that are grazed in both spring and fall should receive about 100 pounds total N per acre, with 60% applied in the winter or early spring and 40% of the N along with any needed P and K in late August or early September. So, producers should plan on applying 60 to 70 lbs N per acre in late winter or early spring, starting as early as January in southeast Kansas or February in the central and northern parts of the state.
Both smooth bromegrass and fescue are efficient users of soil P and K. One of the reasons for this is the dense root system — two to three times more roots per unit of soil volume than corn or soybeans. As a result, these crops can grow and thrive at lower soil test levels than other crops commonly grown in Kansas. But both smooth bromegrass and fescue do remove about 12 pounds of P2O5 and 40 pounds of K2O per ton of hay, which will lower soil test values. Thus, these grasses will respond to P and K fertilization on soils with low or very low soil test levels. Recent work in northeast Kansas has shown response to applied P at soil test levels below 12-15 ppm. P and K application rates should be based on soil tests, as with most crops. In any type of fertilizer management program for tall fescue and smooth bromegrass, whether for hay production or grazing, needed phosphorus and potash should be applied in the late summer or fall for best results, along with a light application of N. Research with smooth bromegrass and fescue production has shown that fall applications of N and P, while these cool-season grasses are still actively growing, will help the grass develop a good root system for the winter, and develop buds for new tillers the next spring. P and K applied in late winter or early spring won’t provide the same benefits. One option for hay production not widely used is to apply all the N, P, and K needed for the following year in late fall, rather than early spring. Research has shown that the yields from a late- fall application are actually higher than from an early spring application, but the protein levels in the hay are slightly lower (a dilution of the N due to higher biomass production). The increased production from a late fall application is due to the stimulation of root growth and production of additional tiller buds.
One additional nutrient producers should be aware of for tall fescue and smooth bromegrass pastures or hayfields is sulfur (S). If the pasture or hayfield is receiving adequate nutrients and precipitation, but is dropping off in production, it could be deficient in S. Sulfur deficiency will cause a general reduction in forage production long before it results in visual deficiency symptoms. An application of S to a tall fescue or smooth bromegrass pasture or hayfield that is deficient in S can result in forage yield increases up to 500 to 800 lbs per acre. Sulfur is taken up by plants as sulfate. If a sulfur application is needed to correct a deficiency in a growing crop, a sulfate-S source should be used, such as ammonium sulfate or gypsum. Elemental sulfur sources can be used if applied far enough in advance of crop uptake needs to allow soil organisms to oxidize the S to sulfate. This will normally take several weeks to months, depending on soil temperature and moisture.
To determine whether P, K, S, and lime are needed on tall fescue and smooth bromegrass fields, producers should consider soil sampling. The best time to sample is in the fall, prior to fertilizer application. However, soil testing can be done in the spring. Samples for a P and K soil test should be taken to a 6-inch depth. A profile S test to a depth of 24 inches should be used to evaluate S needs.
Fall fertilizing also allows Producers to overseed their brome and fescue. One major factor which we all seem to be struggling with is the lack of moisture. It is important that when you overseed to try to overseed right before or right after a rain event to maximize the stand of new grass.
You can no till new seed into existing grass stands or if you wish to start over with a new stand of grass. Moisture is hard to come by right now if you plan to no till I would recommend doing so after a rain event if overseeding or right before in new stand.
The simplest and most common way to do it is to put in a fertilizer buggy with your fertilizer. There are some restrictions with doing it this way. First of all, you will need to check with your local fertilizer dealer to make sure they are ok with mixing in seed in their fertilizer blender. Second fescue and brome seed will not travel as far as the fertilizer… I would recommend a 50-foot double spinner spreader that you will have to half the rate and double spread it aka drive on 25ft centers to get an even seed distribution. Lastly do not spread on a windy day. The wind will have a significant effect on the seed spread pattern.
To conclude
Lonnie Mengarelli is a K-State Research and Extension Agriculture agent assigned to Southwind District. He may be reached at [email protected] or 620-223-3720
K-State Research and Extension is an equal opportunity provider and employer.
Dorivar Ruiz Diaz, Nutrient Management Specialist
[email protected]
Stu Duncan, Northeast Area Crops and Soils Specialist
[email protected]
